-25%
,

Cisco ISR 1100X 8P xDSL GE SFP Router Pluggable SMS/GPS

1,013.04 1,350.72

  • Pluggable SMS/GPS Router

1,013.04 1,350.72

Cisco 1126(X)-8PLTEP/ C1127(X)-8PxLTEP LED Indicators
 

1

VPN

2

PoE LED

3

Status

4

Ethernet Switch Ports 0-7 (0,2,4,6 at the top and 1,3,5,7 at the bottom)

5

GE 0/0/0 RJ45 LED

6

USB5 LED

7

GE 0/0/0 SFP LED

8

Micro USB Console LED

9

CD LED

The following table summarizes the LED indicators that are located in the bezel or chassis of the C111x series.

Table 2. LED Indicators for C111x

Port

LED Color

Description

Control Source

Cisco Logo

Blue

Illuminated Cisco logo. Indicates router power is good.

Bezel side

STATUS

(System Status)

Green and Amber

Steady Green – System operates normally.

Bezel side. All models.

Off—System is not out of reset or BIOS image is not loadable.

Blinking Amber — BIOS/Rommon is booting.

Steady Amber — BIOS/Rommon has completed booting, and the system is at the Rommon prompt or booting the platform software.

VPN OK

Green

Off—No tunnel.

Bezel side

Steady On— At least one tunnel is up.

LTE RSSI/Mode

Green and Amber

No LEDs On—No Service

Bezel Side

1 LED On— RSSI is under -100dBm.

2 LEDs On— Low RSSI, -99dbm <> -90dBm.

3 LEDs On— Medium RSSI -89dBm <> -70dBm.

4 LEDs On— High RSSI, > -69dBm.

Green— LTE

Amber— 3G

GPS

Green

Off: GPS not configured

Bezel Side

On: GPS configured

Blink: GPS Acquiring

WLAN

Green, Red, and Amber

Green— Normal operating condition with at least one wireless client association.

Bezel side

Red—Ethernet link is not operational or Ethernet failure.

Amber—Software upgrade is in progress.

Ethernet Switch GE LAN Ports, Non-PoE

Green

Off— No link

I/O side

Steady On— link

Blink— TXD/RXD data

Ethernet Switch GE LAN Ports, with PoE

Green and Amber

Off— No link, no device powered, PD denied power, power delivery fault PoE administratively disabled.

Green Steady On— link; if PoE device, power is enabled.

Green Blink— TXD/RXD data

Amber – PoE Fault

I/O side

PoE OK

Green

Green Steady On— -53.5V PoE power supply connected and all powered port operating normally.

I/O side

Off — No -53.5V PoE power supply connected to router.

GE WAN Ports

Green

Off— No link

I/O side

Steady On— link

Blink— TXD/RXD data

DSL CD

Green

Off— Shut

I/O Side

Green Blink— Training, or no shut and cable disconnected.

Green Steady On— Trained

DSL Data

Green

Off— No Data Activity

I/O Side

Green Blink— TX/RX Data

Console

Green

Green On— Console enabled.

I/O side

USB Console

Green

Off— No USB device discovered.

I/O side

On— USB device discovered.

USB

Green

Off: No USB device discovered.

I/O Side

On: USB device discovered.

Table 3. LED Indicators for C1101 and C1109

LED

Color

Description

Control Source

Power

Green+Amber

System Power Status

Off: No Power

Green Steady On: Normal operation

Green Blink: Boot up phase or in ROM Monitor mode

Amber Steady on Or Blink: Some issues with the system.

I/O

VPN OK

Green

VPN Status

Off: No tunnel

Steady on:At least one tunnel is up

I/O

Ethernet Switch GE LAN Ports

Green

Link Activity

Off: No link

Steady on: Link

Blink: TXD/RXD Data

I/O

GE WAN Ports

Green

Link Activity

Off: No link

Steady on: Link

Blink: TXD/RXD Data

I/O

LTE DATA/SIM

(C1101-4PLTEPWz C1101-4PLTEP/C1101-4PLTEPWx)

Green and Amber

Single LTE Modem (one modem with SIM switch-over capability)

Off: Modem not up or modem up and no SIM

Amber Steady On: Modem up, SIM installed but not active.

Green Blink: LTE data activity.

Bezel Side

WLAN

(C1101-4PLTEPWx)

3-color LED: Green, Red & Amber;

WLAN Functions

I/O

USB Console

Green

USB Console Status

OFF: USB console not active

ON: USB console active

I/O

USB 3.0

Green

USB 3.0 Status

OFF: No USB device discovered

ON: USB device discovered

USB activity

I/O

Reset Button

The actuation of the Reset button is only recognized during ROMMON boot, that is, as the router comes to the ROMMON prompt.

The Reset button does not require much force to be actuated. The Reset button should be actuated only with a small implement such as the tip of a pen or a paper clip. When the Reset button is pressed at startup, the system LED turns green.

For more information, see the “Reset Overview” section of the Cisco 1100 Software Configuration Guide.

Power Supply

C111x Series ISRs support PoE and PoE+ power to endpoints. The product power specifications are as follows:

  • AC input voltage: Universal 100 to 240 VAC

  • Frequency: 50 to 60 Hz

  • Maximum output power: Up to 66W for non-PoE supply and upto 150W for PoE supply

  • Optional PoE and PoE+

  • Output voltage: +12VDC for system power and -53.5VDC for PoE power

Slots and Interfaces

About Slots, Subslots, and Port Numbering

The Cisco 1100 series designates its interfaces using a 3-tuple notation that lists the slot, sub slot and port in the format slot/sub-slot/port. The slot number is reserved for the mother board, which is “0”. Each interface type is allocated a sub slot and the port number is a unique port on the interface.

Table 4. Slot, Bay, and Port Numbering

Subslot

Interface Type

0

Ethernet LAN

1

Ethernet WAN

2

LTE

3

DSL

4

WIFI

Periodic Inspection and Cleaning

We recommend that you periodically inspect and clean the external surface of the router is recommended to minimize the negative impact of environmental dust or debris. The frequency of inspection and cleaning is dependent upon the severity of the environmental conditions, but we recommend a minimum once every six months. Cleaning involves vacuuming router air intake and exhaust vents.

Based on 0 reviews

0.0 overall
0
0
0
0
0

Only logged in customers who have purchased this product may leave a review.

There are no reviews yet.